mikesmarinefiberglassrepair.com

On August first I got a call at 8 thirty in the morning , from Brest Bay Marina for a estimate , on a 28 foot Proline with bottom damage , so I wentWell I wrote a estimate too acid wash the bottom first 8/1/2019 So I met the owner that evening an Josh pointed out what he wanted repairWe can too a price an I help Josh put his boat in the water the night before . Now it is the next morning at Brest Bay marina 8/2/2019 It is going on a work rackA pretty dirty bottom , but I can do this , after 3 to 4 hours of spraying acid an hand washingYes it is the same boatFront an the back is clean 8/2Clean ah? Its lunch time , when I get back , I will buff the front bottom where the damage is at 8/2So after lunch I buff the front bottom surface an than work on the color , working on the repairs an doing the body workLooks pretty close , I sent a picture text too Josh an he thought so too , so I finish up the repairs an tape off an sprayed the gel coat onI got it sprayed 8/2See repair an gel coat letting it dry for tomorrow morning . If anything I got a good base , Hopefully know one touchs it , or May flies get in it or the local racoon gets his tale in it . But it should dry quick in this temp., It was 83 here at Brest Bay Marina today .....8/2/2019 until tomorrow.............The color is a little lighter , so I am going too darken the color I mix , with tan ,gold , an gray an re-sprayed it 8/3I have it the surface sanded an ready too spray Saturday morning at Brest Bay Marina 8/3/2019There now that looks closer . 8/3/2019Yes it Sunday morning 8 a.m. I wet sanded an buff the surface that I repair an gelcoat 8/4.2019Another viewFinish . . . . . . 8/4/2019

Andy stop out for a buff an waxI took off the side bunks too acid wash the sides 8/12/2019Bunks are off , now I can buff the sidesThe strains are off the surfacesYellow strains are gone 8/12 I remove the lettering on both side 8/13I started too buff the hull 8/13/2019I have both sides buff 8/14-15 I had the customer come over too ok the repairs on his boatThis chip &Repaired , Gelcoat & wet sanded an buffed .8/21This one on the backwet sanded an buff the repairs 8/21Bunks back on the repairs are fix 8/21TheseAn this scratch in front of the chips under the waterline 8/20Bottom front repair , this is the back part This is where the corner is ripped off an has a hole on it Middle Part 8/20This is the front of this repair it about 5 feet long , all the repairs are under the waterline 8/20I did the body work an sprayed the gelcoat on 8/21I found 5 chips on the chirms , I body worked them an sprayed the gelcoat on , letting it dry 8/21 . HOT Day todayI have the bottom wet sanded an buff and look the chips an ripped is gone 8/22/2019Buff an waxBuff an wax 8/23/2019Done and back together 8/23/2019

Today Ron from Triple DDD Tree Service stop out with their bucket truck8/5/2019 so we took off the bucket it needs some fiberglass repair all broken up an both cornersleft side ready for fiberglassingright side grinded an ready for fiberglassI have 3 sheets made 22 inches wide by 3 foot deep an I made the corner matting 8/5 Put the resin an rolled out the air bubbles out of the matting 8/5 Letting it drydryingDrying for tomorrow 8/5I fiberglass the outerside corners 8/6letting them dry 8/6I did some body work an filler on chips on the corners edge 8/6So it started too rain , so now I am inside , I mix some white gelcoat up too seal off thr fiberglass an roll it on . . . .8/6I started early this morning an by 8 a.m. I had one side fiberglass 8/7/2019Both mounts are repair an fiberglass drying in the sun , after lunch I sanded an gelcoated the surface too seal it off ,8/7/2019Drying in the sun (Gelcoated) 8/7/2019.........................I started a 26 footer sailboat 2012 wet sanded an buffThe customer started this job an quit in the middle of it. Now I am going too try too straighten it up too make it shiney again 8/7,8,9/2019I have it all wet sanded an the boats in the building ready too buff 8/10ready too buff , I started on the left sideI started with the top half of the boat 8/10Getting shiney , this is the black 8/10/2019I started on the left side of the hull 8/11/2019Looked at that 8/11/2019Here is the right side wet sandedHere is the same spot an buffedan repair  , but the next day 8/12/2019Top half of the boat wet sanded 8/11/2019Buff 8/13Wet sanded surface , ready to be buffed 8/11/2019Buff 8/13 I have the right side hull buffed &I have this part of the top buffed 8/12/2019I have the right side top buff an shiney 8/13Another view of the top 8/13I also buff the cockpit I  clean up the glass door too the cabine 8/13 I pulled it outside an washed it 8/14 . . .  3 hour wash , I got her clean I been doing repairs 8/ 17 Refinish 8/18spider cracks on toe rail areaAnother spot of spider cracks Refinishall repaired 8/19this was a crack in the black repair an sprayed black , it dry than I wet sanded it Buff the surface an the crack is gone 8/20More touch ups 8/22Refinish letting it dryOne more touch up Refinish letting it dry , an a lot of chips in the non-skid 8/28 /2019 ...............................................On 8/20 Tracker Boat Center from Rossford ,Ohio stop out with a 2020 Tahoe 215 XI with somewith this on itsome gelcoat drops on the non-skid an a unfinished factory repairSo I cover the boat too protect the windsheild I don't want white dots or over spray on a new boat ? ? ? So I took off the clete 8/20an the inside panel too get at the nutsoff of the sideI wet sanded the repair an buff it until it shine 8/20/2019See back together an shiney I started too clean up the non-skid The gelcoat drops are goneand on the smooth , tomorrow I will wash the boat check it over , and ship it 8/20Washing the boat 8/21/2019Done ....Back on the sailboatStarted my touch-ups 8/23The color I mix is pretty close 8/23I have some repairs in the white .Old screw holes yaaaaaa 11 of them .Got some sprayed white White again 8/23/2019Looks better now 8/29/2019 almost done with all the touch upsLooked at that eflection 8/31 . Done .